Your Best Choice for Furnace and Air Conditioning Repair in Monroe, MI (2)

Performed furnace tune up and evaluation on an American standard system; pulled and cleaned the burners and flame sensors.

Performed boiler tune up and evaluation on a Well-McLain system; found no issues at this time.

Performed furnace tune up and evaluation on a Rheem system; found the blower wheel and ductwork dirty, also verified furnace operations.

Performed furnace tune up and evaluation on a Carrier system; found filter and humidifier pads were dirty, changed both and verified operations.

Performed furnace tune up and evaluation on a Goodman system; found the blower wheel dirty but all other components were okay at this time.

Performed furnace tune up and evaluation on a Goodman system, found all components working okay at this time.

Performed furnace tune up and evaluation on a Rudd system; cleaned burners, flame sensor and ignitor. Verified furnace operations and all else was okay at this time.

Performed furnace tune up and evaluation on a Goodman system; found the heat exchanger had failed.

Performed furnace tune up and evaluation on a Coleman system; found all components working at this time, verified operations and supplied customer with new filters.

Replaced pressure reducing valve, pressure relief valve, and back flow preventer on an old Weil McClain boiler

Performed furnace tune up and evaluation on a Trane system; upon further inspection found a dirty evaporator coil, blower motor and the capacitor out of range.

Performed furnace evaluation and inspection on a Coleman system; found a bad inducer motor, replaced the motor and did a system rejuvenation.

Performed furnace evaluation and inspection on a Coleman system; upon arrival found the gas valve not opening, cycled the furnace once it opened and confirmed operations.

Performed furnace evaluation and inspection on a Coleman system; found the unit flashing an error code, shortened tubing to the transducer switch and verified furnace operations.

Performed furnace evaluation and inspection on a Coleman system; found water in the inducer motor due to draining problem, fixed draining issue and verified operations.

Performed furnace evaluation and inspection on a Coleman system; found the pressure switch not closing due to the inducer motor, after testing voltage found the motor had failed. Replaced inducer motor and verified operations.

Performed furnace evaluation and inspection on a Carrier system; upon arrival found the limit was tripped and the bottom cabinet door was removed, replaced the cabinet door and verified operations.

Performed furnace evaluation and repair on a Goodman system; found a bad control board, replaced and installed a new surge protector for additional protection.

Performed furnace tune up and evaluation on a Coleman system; upon further inspection found faulty circuit board. Replaced circuit board under warranty and installed surge protector for added protection.

Performed furnace tune up and evaluation on a National Comfort Product system; upon arrival found the W wire from thermostat loose at furnace and surge protector burnt out. Reconnected the wire and replaced the surge protector.

Performed furnace tune up and evaluation on a Rheem system; found the hose clamp for the drain not tight, re-tightened the hose clamp and all else was okay.

Performed furnace fall tune up on a Garrison system; verified furnace operations and all components were okay at this time.

Performed furnace tune up on a Rheem system for one of our maintenance club members.

Performed furnace evaluation and inspection on a Coleman system; upon further inspection found buildup on the blower motor, weak blower capacitor and leaking gas connector. Cleaned the blower motor and replaced the capacitor and gas connector.

Performed a boiler tune up and evaluation on a HydroTherm system; cleaned burners, pilot assembly and verified operation.

Performed furnace tune up and evaluation on a Carrier system; found all components working at this time.

Performed furnace evaluation and safety inspection on a Carrier system; cleaned the burners, flame sensors and drain line. All other components were okay at this time.

Performed furnace evaluation and inspection on a Coleman system; upon arrival the furnace giving a vent termination code, found a walnut blocking the exhaust. Removed the walnut and verified furnace operations.

Performed boiler inspection and evaluation; during inspection we found the thermostat set to electric heat, changed settings to gas heat and cycled both the air conditioner and boiler.

Performed furnace tune up on a Goodman system for one of our VIP customers; replaced filter and all else was okay at this time.

Performed tune up and evaluation on a Coleman furnace; found excess humidity due to A/C not running since it is not at the set temperature. Set the fan to consistent ON to move air around the house.

Performed furnace tune up and evaluation on a Coleman system; all components were working perfectly fine.

Performed furnace tune up and evaluation on a Coleman system; found the evaporator coil and blower wheel dirty, performed a system rejuvenation and all else was fine.

Performed furnace tune up and evaluation on a Coleman system for our VIP customer; found all components working at this time

Performed furnace tune up and evaluation on a Coleman system; found all components working as they should.

Performed a furnace tune up and evaluation on a Carrier system; found the blower wheel and the evaporator coil caked in dirt, cleaned both items and all else was okay at this time.

Performed air conditioner inspection and evaluation; upon further inspection found dual capacitor and the condenser fan motor failed, also found burnt wires. Customer chose to go with a free estimate for new AC.

Performing an annual furnace tune up on a Goodman system; upon further inspection found a failed flame sensor and dirty ductwork.

Performing air conditioning system evaluation and inspection; found a bad dual capacitor and condenser impacted with dirt, replaced dual capacitor and cleaned unit.

Preforming an end of summer furnace maintenance, on a Miller manufactured home furnace.

Serviced a 2008, high efficiency Carrier Furnace; found the pressure switch not closing, customer stated the fan for the A/C also doesn't spin. Replaced the pressure switch for the furnace and the dual capacitor for the A/C.